| B-Curve AC MCB | Residential Lighting General-purpose final circuits with low inrush current, such as lighting and socket circuits. | The instantaneous magnetic trip range is typically 3–5 × In under IEC 60898-1. Common ratings are selected according to the cable capacity and design current; ratings such as 6 A, 10 A, 16 A, 20 A, and 32 A are widely used but are not universal. | Install on the correct AC supply system and verify the number of poles, rated voltage, busbar compatibility, conductor size, enclosure space, and terminal access. The protective device must not be rated above the permitted current-carrying capacity of the circuit conductors. | Confirm continuity, polarity, protective-conductor continuity, insulation condition, and fault-loop or prospective-fault parameters as required by local rules. Verify that the device is firmly seated and that the circuit operates without nuisance tripping. | Check for discoloration, heat damage, loose connections, mechanical stiffness, and repeated unexplained trips. Replace with the same or a compatible approved curve, pole count, voltage, current rating, and breaking capacity. | A practical choice for low-inrush circuits where standard residential or light-commercial protection is required. |
| C-Curve AC MCB | Commercial Motors Small motors, pumps, transformers, LED drivers, and other loads with moderate starting or energization current. | The instantaneous magnetic trip range is typically 5–10 × In under IEC 60898-1. It tolerates more inrush than a B-curve device, but it still requires coordination with cable capacity and fault-current levels. | Confirm that the expected starting current will not cause unwanted tripping. Check voltage, frequency, pole configuration, conductor termination, enclosure temperature, and the manufacturer’s allowable grouping or derating information. | Test operation under normal load and, where needed, use calibrated equipment to verify trip characteristics. Confirm that the measured fault-loop impedance or prospective short-circuit current is compatible with the device’s interrupting rating. | Investigate frequent trips before increasing the breaker rating; the cause may be overload, motor faults, low voltage, or excessive inrush. Replacement must preserve the original protection curve unless a qualified design review authorizes a change. | Often the most versatile option for global commercial and light-industrial applications, subject to local code and coordination. |
| D-Curve AC MCB | High Inrush Industrial Transformers, welding equipment, large motors, and other loads with high short-duration starting current. | The instantaneous magnetic trip range is typically 10–20 × In under IEC 60898-1. A D-curve device may permit substantial inrush, so short-circuit protection and disconnection requirements need careful verification. | Use only after confirming the load profile, minimum fault current, cable protection, and required automatic disconnection time. D-curve selection may be unsuitable where the available fault current is too low to operate the magnetic trip promptly. | Measure or calculate prospective fault current and fault-loop impedance. Test the circuit under controlled starting conditions and confirm that normal starting does not trip the breaker while fault protection remains effective. | Inspect terminals and conductors for thermal stress caused by repeated starts. Do not substitute a D-curve for a B- or C-curve merely to stop nuisance tripping; correct the underlying load, cable, or coordination issue first. | Suitable for selected industrial loads, but less suitable as a default choice for ordinary final circuits. |
| 1-Pole AC MCB | Single-phase final circuits where only the phase or line conductor is individually protected and switched. | Usually provides overcurrent protection in one conductor. The exact rated voltage, neutral arrangement, breaking capacity, and isolation requirements vary by national wiring practice. | Connect the line conductor to the correct terminal and follow the indicated supply direction where the product requires it. Confirm that the neutral is handled as required by the local wiring system and that the enclosure provides adequate touch protection. | Verify line-to-neutral voltage, polarity, continuity, insulation resistance where appropriate, and protective-conductor continuity. Functional switching should be performed with the circuit in a safe condition. | Check terminal heating, signs of arcing, and correct labeling. Replacement requires matching the original terminal orientation, rating, curve, breaking capacity, mounting system, and approval requirements. | Space-efficient for many single-phase distribution boards, but not appropriate where simultaneous neutral isolation is required. |
| 1P+N MCB | Single-phase circuits where the line is protected and both line and neutral are disconnected by a linked mechanism. | Depending on the design, the neutral pole may be switched but not independently overcurrent-protected. The product marking must be checked to distinguish a switched neutral from a protected neutral. | Ensure line and neutral are connected to the correct terminals and that the device is approved for the local supply arrangement. Confirm neutral continuity and avoid mixing neutral conductors between circuits. | Test polarity, line-neutral voltage, neutral continuity, protective-conductor continuity, insulation condition, and the linked operation of both poles. | Inspect the linked mechanism and neutral terminal for heat or looseness. Replace the complete device if the linkage, line pole, or neutral contact is damaged; do not treat it as two unrelated single-pole devices. | Useful where compact simultaneous isolation is desired on single-phase circuits. |
| 2-Pole AC MCB | Single-phase circuits requiring simultaneous disconnection of line and neutral, or two-conductor systems where both conductors require protection. | Both poles are mechanically linked; whether both poles have overcurrent protection depends on the device design. Rated voltage and pole configuration must match the supply system. | Confirm the permitted use on the local earthing and distribution system. Connect conductors according to the terminal markings and maintain separation between circuits with shared or incorrectly identified neutrals. | Verify the voltage between conductors, polarity, continuity, insulation condition, and simultaneous opening. Confirm protective-disconnection performance using the test method required by local regulations. | Look for contact wear, loose terminals, overheating, and difficult operation. Replace with a two-pole device having equivalent protection, isolation, voltage, current, curve, and breaking-capacity characteristics. | Appropriate when full two-conductor isolation is required or preferred by the installation design. |
| 3-Pole AC MCB | Three-phase motors, heaters, and balanced or unbalanced three-phase circuits without a switched neutral requirement. | Provides linked protection and switching for three live conductors. The selected rating must coordinate with all phase conductors, the load current, motor starting conditions, and the available short-circuit current. | Confirm phase sequence where relevant, correct torque for all terminals, enclosure clearances, busbar arrangement, and conductor identification. Do not use the breaker as a substitute for a motor starter or overload relay where those functions are required. | Check phase-to-phase voltage, phase sequence, continuity of each pole, insulation condition, protective-conductor continuity, and trip performance. Test motor rotation only after safe energization procedures are complete. | Inspect all three poles for uneven heating, loose connections, contact wear, and mechanical linkage problems. Replace the complete linked unit if one pole is damaged unless the design expressly permits another service method. | A common configuration for three-phase final circuits and small industrial loads. |
| 4-Pole AC MCB | Three-phase, four-wire systems where simultaneous disconnection of three phases and neutral is required. | The neutral pole may be switched only or may have a specified protection function; this must be confirmed from the product marking. Selection depends on the supply arrangement, neutral loading, and local isolation rules. | Identify all phases and the neutral correctly, verify the neutral pole position, and confirm that the device is suitable for the system earthing arrangement. Pay close attention to conductor routing and terminal torque. | Verify phase-to-phase and phase-to-neutral voltages, phase sequence, neutral continuity, insulation condition, protective-conductor continuity, and simultaneous operation of all poles. | Examine the neutral pole and linkage for overheating or mechanical damage, particularly where harmonic currents or unbalanced loads are present. Replacement must match the exact pole arrangement and neutral function. | Suitable for selected three-phase, four-wire installations needing comprehensive isolation. |
| DC MCB | Photovoltaic strings, battery systems, control circuits, telecommunications, and other direct-current applications. | DC arcs do not naturally extinguish at a current zero, so DC-rated devices require a specified voltage, current, polarity, pole arrangement, and interrupting capacity. AC-only MCBs must not be assumed suitable for DC. | Confirm the maximum DC voltage, prospective DC fault current, polarity marking, series-pole requirements, conductor insulation, and minimum isolation distance. Follow the specified connection direction and use DC-rated accessories. | Test polarity, open-circuit voltage, insulation condition, continuity, and functional operation with suitable DC-rated test equipment. Avoid disconnecting live PV or battery circuits unless the equipment is specifically designed for that operation. | Inspect for contact erosion, heat damage, polarity errors, and signs of DC arcing. Replace only with a device having equal or higher DC voltage and interrupting capability and the same system-specific configuration. | Essential for DC circuits; selection must be based on the complete DC system rather than on an equivalent AC current rating. |
| High-Breaking-Capacity MCB | Installations with high prospective short-circuit current, including dense commercial, industrial, and utility-connected distribution systems. | Interrupting ratings commonly include values such as 4.5 kA, 6 kA, or 10 kA, but the correct value depends on the applicable standard, voltage, pole arrangement, and tested product configuration. | Determine the prospective short-circuit current at the installation point before selection. Confirm discrimination, cascading or backup protection conditions, busbar compatibility, and enclosure fault-containment requirements. | Verify the calculated or measured fault level, installation polarity, conductor integrity, and protective-disconnection performance. Do not perform deliberate short-circuit tests in the field. | Treat any device that has interrupted a significant fault as requiring inspection and possible replacement according to its documentation. Check for casing deformation, odor, discoloration, and stiff operation. | Preferred where the available fault current exceeds the rating of standard low-capacity MCBs. |
| Thermal-Magnetic MCB | General overcurrent protection combining long-duration overload protection with rapid short-circuit protection. | The thermal element responds to sustained overcurrent and is affected by ambient temperature; the magnetic element responds rapidly to high fault current. Trip curves and temperature correction vary by design. | Apply the manufacturer’s ambient-temperature and grouping information. Ensure conductors are protected against both overload and short circuit, and provide adequate ventilation where the enclosure generates heat. | Confirm rated voltage, current, curve, continuity, insulation condition, fault-loop parameters, and operational behavior. Use calibrated trip-test equipment when a time-current verification is required. | Do not repeatedly reset a tripped device without identifying the cause. Inspect for overload evidence, terminal heating, contamination, and mechanical wear; replace units that fail to reset or trip consistently. | The standard choice for many low-voltage distribution applications when correctly coordinated. |
Distributors 
SDS Download 
Contact 
